Urethane

Recommended as a topcoat for Specialty Polymer Coatings Inc. SP-5885 and other SPC epoxy coatings where UV protection and colour and gloss retention are primary considerations.

Epoxy

SP-1288 G.P. Epoxy is a two-component ambient cured epoxy based on novel leading edge technology. SP-1288 G.P. Epoxy can be used in applications where abrasive blasting is not possible or feasible. SP-1288 G.P. Epoxy exhibits excellent adhesion on metal substrates prepared as per SSPC SP-11 Surface Preparation Specification.

Epoxy

SP-2832 is a 100% solids technologically advanced epoxy coating for use in the Oil and Gas Industry. It has superior anti-corrosive properties on the exterior of steel pipelines for above and below ground service.

Epoxy / Urethane

Used for coating of girth welds, as well as valves, fittings, pipe, ballast tanks, ships and marine structures. Ideally suited for coating of pipe to be used for slip bore/directional drilling due to its superior abrasion, impact and gouge resistance properties. Also for exterior coatings of pipelines in buried or immersed services. Advantage: excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy and Fiber Reinforced Plastic

Epoxy / Urethane

Used for exterior coatings for pipelines in buried or immersed services and slip bore and directional drilling applications. Advantages: Excellent abrasion and impact resistance and excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy, and Fiber Reinforced Plastic.

Epoxy

Used for high temperature operating pipelines, compressor / pump station discharge piping, recycle lines, valves, fittings, girth weld coatings, rehabilitation of existing pipelines, and suitable for certain tank lining applications. Advantages: excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy, liquid epoxy, and urethane coatings.

Epoxy

Used for coating pipelines, structures or other steel surfaces where the surface is damp due to environment, high humidity or condensation. Advantages: excellent adhesion to wet, damp or dry grit blasted steel surfaces, Fusion Bond Epoxy, and Fiber Reinforced Plastic.

Epoxy

DISCONTINUED. Excellent corrosion protection for steel structures, bridges, tanks, piping, valves, and other steel surfaces exposed to coastal and/or moderate to severe industrial environments.

Polymer

Used as a tie-coat on well cured two-component coating in areas where abrasive blasting cannot be employed.

Epoxy

SP-5885 SF replaces SP-5885. It is used for lining of tanks, piping and structures containing salt water, jet fuel, aliphatic hydrocarbons and associated products. Also used as corrosion resistant coating for structural steel, storage tanks and equipment in refineries pulp and paper mills and chemical plants.

Acrylic

Used as a protective and decorative finish coat on the exterior of above ground pipelines and structural finish coat on the exterior of above ground pipelines and structural steel. Also suitable for use in areas where other coatings that contain isocyanates may be prohibited.

Epoxy

Used for coating of pipe, valves, fittings, girth weld coatings, tank lining, rehabilitation of existing pipelines and slip bore/direction drill applications. Advantage of excellent adhesion to grit blasted steel surfaces, fusion bond epoxy, liquid epoxy, and urethane coatings.

Novalac

Used for exterior coatings of pipe, valves and fittings used in buried or immersed services. Advantages: good flexibility, excellent impact resistance, excellent resistance to high temperature cathodic disbonding up to 150 degrees C and excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy and Fiber Reinforced Plastic.

Ceramic Phenolic Novalac Epoxy

SP-8988 is a unique “Ceramic Phenolic Novalac Epoxy” composite pipe coating. The highly cross-linked Ceramic Phenolic Novalac Epoxy matrix makes SP-8988 pipe coating ideal for high temperature service, cathodic disbonding resistance up to 180°C (356°F). Superior hot pull off adhesion even on 150°C (302°F) coating surface. SP-8988 provides long lasting wear and abrasion resistance plus excellent corrosion protection.

Epoxy

SP-9800 is a two component ambient cure epoxy Gas Transmission Pipe Flow Efficiency coating. It is a coating for Internal Gas Transmission Pipelines to improve gas flow and corrosion protection. SP-9800 meets the requirements of API Specification RP 5L2. Advantages: • 100% Solids - No VOCs. • Good flexibility. • Excellent water resistance. • Excellent anti-corrosion protection during storage life.

Novalac Epoxy

SP-9887 GF is a Glass Flake reinforced Novalac epoxy coating for use on tanks, pipes, steel structures, offshore platforms and subsea structures. SP-9887 GF cures to form a coating film with overlapping layers of glass flakes that resists water and chemical permeation. SP-9887 GF can be used as a lining for storage tanks, ballast tanks, separation vessels, sewage tanks and digesters, waste troughs, and pipelines containing crude oil.