REPAIR PRODUCTS

Product
Coating Type
Description
Epoxy
SP-1288 G.P. Epoxy is a two-component ambient cured epoxy based on novel leading edge technology. SP-1288 G.P. Epoxy can be used in applications where abrasive blasting is not possible or feasible. SP-1288 G.P. Epoxy exhibits excellent adhesion on metal substrates prepared as per SSPC SP-11 Surface Preparation Specification.
Polyurethane
Ideally used for coating of pipe intended for slip bore/directional drill applications. Also for coating of pipe, valves, fittings, fabricated assemblies, girth welds, rehabilitation (recoating) of existing pipelines and coating repairs.
SP-1853
Updated
Polyurethane
Used for coating of ship decks, on-shore and off-shore structures and marine piles.
Polyurethane
Used for coating of ship hulls, rudders, marine pilings, docks and ballast tanks. Ideally used for coating of pipe intended for slip bore/directional drill applications and for rehabilitating large sections of existing pipeline with automated equipment. Also for coating of pipe, valves, fittings, fabricated assemblies, girth welds, rehabilitation (recoating) of existing pipelines and coating repairs.
Anode Fill Epoxy
Ideally used as coating protection for CP test leads, anode and drain lead connections to pipelines. Also used to fill the annular area between anode bracelets on pipelines. Advantages: Isocyanate free, fast setting, cures underwater, high build properties, primerless and good adhesion to steel substrates, Fusion Bonded Epoxy and Fiber Reinforced Plastic.
Epoxy / Amine
Used for grouting and sealing purposes on pipeline prior to installation of repair/reinforcing sleeves or clamps, hot tape fittings and split sleeve fittings.
Epoxy
Used for coating of pipe, valves, fittings, girth welds and rehabilitation of existing pipelines in cool weather and on facilities operating at low temperatures. Advantages: High build single coat application, isocyanate free, excellent cathodic disbondment performance at temperatures up to 65 degrees C (149 degrees F), and excellent adhesion to grit blasted steel surfaces, fusion bond epoxy and Fiber Reinforced Plastic.
Epoxy
SP-2832 is a 100% solids technologically advanced epoxy coating for use in the Oil and Gas Industry. It has superior anti-corrosive properties on the exterior of steel pipelines for above and below ground service.
Epoxy / Urethane
Used for coating of girth welds, as well as valves, fittings, pipe, ballast tanks, ships and marine structures. Ideally suited for coating of pipe to be used for slip bore/directional drilling due to its superior abrasion, impact and gouge resistance properties. Also for exterior coatings of pipelines in buried or immersed services. Advantage: excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy and Fiber Reinforced Plastic
Epoxy / Urethane
Used for exterior coatings for pipelines in buried or immersed services and slip bore and directional drilling applications. Advantages: Excellent abrasion and impact resistance and excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy, and Fiber Reinforced Plastic.
Epoxy
Used for high temperature operating pipelines, compressor / pump station discharge piping, recycle lines, valves, fittings, girth weld coatings, rehabilitation of existing pipelines, and suitable for certain tank lining applications. Advantages: excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy, liquid epoxy, and urethane coatings.
SP-4888
Updated
Epoxy
Used for coating pipelines, structures or other steel surfaces where the surface is damp due to environment, high humidity or condensation. Advantages: excellent adhesion to wet, damp or dry grit blasted steel surfaces, Fusion Bond Epoxy, and Fiber Reinforced Plastic.
Epoxy
SP-5885 SF replaces SP-5885. It is used for lining of tanks, piping and structures containing salt water, jet fuel, aliphatic hydrocarbons and associated products. Also used as corrosion resistant coating for structural steel, storage tanks and equipment in refineries pulp and paper mills and chemical plants.
Epoxy
Used for coating of pipe, valves, fittings, girth weld coatings, tank lining, rehabilitation of existing pipelines and slip bore/direction drill applications. Advantage of excellent adhesion to grit blasted steel surfaces, fusion bond epoxy, liquid epoxy, and urethane coatings.
Novolac
Used for exterior coatings of pipe, valves and fittings used in buried or immersed services. Advantages: good flexibility, excellent impact resistance, excellent resistance to high temperature cathodic disbonding up to 150 degrees C and excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy and Fiber Reinforced Plastic.
SP-8988
Updated
Ceramic Phenolic Novolac Epoxy
SP-8988 is a unique “Ceramic Phenolic Novolac Epoxy” composite pipe coating. The highly cross-linked Ceramic Phenolic Novolac Epoxy matrix makes SP-8988 pipe coating ideal for high temperature service, cathodic disbonding resistance up to 180°C (356°F). Superior hot pull off adhesion even on 150°C (302°F) coating surface. SP-8988 provides long lasting wear and abrasion resistance plus excellent corrosion protection.
Epoxy
SP-9800 is a two component ambient cure epoxy Gas Transmission Pipe Flow Efficiency coating. It is a coating for Internal Gas Transmission Pipelines to improve gas flow and corrosion protection. SP-9800 meets the requirements of API Specification RP 5L2. Advantages: • 100% Solids - No VOCs. • Good flexibility. • Excellent water resistance. • Excellent anti-corrosion protection during storage life.
Modified Epoxy Novolac
SP-9890 is SPC’s latest development in tank lining technology. Uses include storage tanks, sewer and waste treatment plants. To order SP-9890 or if you have any questions please call or email SPC, via the above link.
 
     
© 2003 Specialty Polymer Coatings Inc.