ALL MARINE PRODUCTS

Product Coating Type Description

SP-1088

Urethane Recommended as a topcoat for Specialty Polymer Coatings Inc. SP-5885 and other SPC epoxy coatings where UV protection and colour and gloss retention are primary considerations.

SP-1288 G.P.

Epoxy SP-1288 G.P. Epoxy is a two-component ambient cured epoxy based on novel leading edge technology. SP-1288 G.P. Epoxy can be used in applications where abrasive blasting is not possible or feasible. SP-1288 G.P. Epoxy exhibits excellent adhesion on metal substrates prepared as per SSPC SP-11 Surface Preparation Specification.

SP-1386
Updated

Polyurethane Recommended uses for coating of On-shore and off-shore structures and pipe, sewer lines, general piping, dam gates, penstocks, lining of tanks and sewage digesters, lining of open-top gondola railcars used for transporting sulphur and coal. Advantages: good flexibility, excellent resistance to sea and fresh water, good acid and abrasion resistance, excellent adhesion to steel surfaces, fusion bonded epoxy, Fiber Reinforced Plastic and concrete.

SP-1853

Polyurethane Used for coating of ship decks, on-shore and off-shore structures and marine piles.

SP-1864

Polyurethane Used for coating of ship hulls, rudders, marine pilings, docks and ballast tanks. Ideally used for coating of pipe intended for slip bore/directional drill applications and for rehabilitating large sections of existing pipeline with automated equipment. Also for coating of pipe, valves, fittings, fabricated assemblies, girth welds, rehabilitation (recoating) of existing pipelines and coating repairs.

SP-2700

Abrade-Guard Used for coating of surfaces of decks, ramps, pipelines and other structures that are exposed to severe abrasion and impact. Also for coating of concrete flooring subject to chemical spillage.

SP-2830

Epoxy / Amine Used for grouting and sealing purposes on pipeline prior to installation of repair/reinforcing sleeves or clamps, hot tape fittings and split sleeve fittings.

SP-2888 R.G.
Updated

Epoxy / Urethane Used for coating of girth welds, as well as valves, fittings, pipe, ballast tanks, ships and marine structures. Ideally suited for coating of pipe to be used for slip bore/directional drilling due to its superior abrasion, impact and gouge resistance properties. Also for exterior coatings of pipelines in buried or immersed services. Advantage: excellent adhesion to grit blasted steel surfaces, Fusion Bond Epoxy and Fiber Reinforced Plastic

SP-4888

Epoxy Used for coating pipelines, structures or other steel surfaces where the surface is damp due to environment, high humidity or condensation. Advantages: excellent adhesion to wet, damp or dry grit blasted steel surfaces, Fusion Bond Epoxy, and Fiber Reinforced Plastic.

SP-5818

Epoxy DISCONTINUED. Excellent corrosion protection for steel structures, bridges, tanks, piping, valves, and other steel surfaces exposed to coastal and/or moderate to severe industrial environments.

SP-5819

Polymer Used as a tie-coat on well cured two-component coating in areas where abrasive blasting cannot be employed.

SP-5885

Epoxy SP-5885 SF replaces SP-5885. It is used for lining of tanks, piping and structures containing salt water, jet fuel, aliphatic hydrocarbons and associated products. Also used as corrosion resistant coating for structural steel, storage tanks and equipment in refineries pulp and paper mills and chemical plants.

SP-5890

Acrylic Used as a protective and decorative finish coat on the exterior of above ground pipelines and structural finish coat on the exterior of above ground pipelines and structural steel. Also suitable for use in areas where other coatings that contain isocyanates may be prohibited.

SP-5891 DTM

Acrylic Used as a protective coating on the exterior of above ground domestic or industrial storages tanks, piping and structural steel.SP-5891 is suitable for use in areas where other coatings that contain isocyanates may be prohibited. Can also be used as a topcoat for SP-1868 Tuff-Tank and may be applied wet to wet.

SP-6888

Epoxy Used for coating of pipe, valves, fittings, girth weld coatings, tank lining, rehabilitation of existing pipelines and slip bore/direction drill applications. Advantage of excellent adhesion to grit blasted steel surfaces, fusion bond epoxy, liquid epoxy, and urethane coatings.

SP-6889

Epoxy Used for lining of ballast tanks and penstocks. It is a corrosion resistant coating for structural steel, storage tanks, and equipment in refineries, pulp and paper mills and chemical plants. Advantages: good adhesion to marginally prepared surface, single coat application to mil thickness normally requiring two or three coats.

SP-7888 NSF 100% Solids Epoxy
Updated

Epoxy Used for lining of water storage tanks and pipelines, coating for water and sewage treatment plants, coating for dam gates and penstocks.

SP-9887

Novalac Epoxy SP-9887 GF is a Glass Flake reinforced Novalac epoxy coating for use on tanks, pipes, steel structures, offshore platforms and subsea structures. SP-9887 GF cures to form a coating film with overlapping layers of glass flakes that resists water and chemical permeation. SP-9887 GF can be used as a lining for storage tanks, ballast tanks, separation vessels, sewage tanks and digesters, waste troughs, and pipelines containing crude oil.

SP-9888
Updated

Novalac Used for internal lining of storage tanks and sewage digesters. Advantages: good flexibility, excellent impact resistance and excellent resistance to high temperature cathodic disbonding up to 150 degrees C.

SP-100
Updated

Equipment Wash Spray machine cleaner.

SP-110
Updated

Tool Cleaner Dissolving gel or cured coatings

SP-120

Internal Storage Lubricant Internal storage lubricant for spray machine, when the spray machine is not in use.

SP-140

Epoxy Thinner Solvent

SP-150

Polyurethane Thinner Solvent

SP-1866 HTP

Polyurethane SP-1866 HTP (High Temperature Polyurethane) is a "Coal Tar Free" 100% Solids Polyurethane coating designed for pipeline operating at high temperature. SP-1866 HTP coating can also be used in Industrial applications where the acid resistance and superior abrasion resistance properties of Polyurethane coating are required. Single coat application provides superior adhesion, impact and chemical resistance.
 
       
© 2003 Specialty Polymer Coatings Inc.